Learning the Basics of Plumbing for Bathtub Installation
CallEach person seems to have their own theory with regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably difficult project. If the old tub is easily accessible, the task can relocate rapidly; if you have to open up a wall to remove the old tub and also place the brand-new bath tub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have certified on your own for the task and are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to think about using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly aid you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as do not need to transform the arrangement of your previous water pipes.
Your tools and material list must consist of the following:
Preparing for the Installment
Firstly, the sustaining framework provided with the bath ought to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome due to the restricted accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, put the tub in the required position. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap port to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Switch on the water supply and also check all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as also check the overflow outlet and the normal outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the bath tub has actually been used at the very least when as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Secure the faucet in place with the manufacturer given backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a stiff seal, causing the water to pass through the wall in between the bath and the tiling, leading to difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the motion experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily readily available on the marketplace. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that editorial about Installing A Bathtub from a friend on another domain. Do you know about somebody who is sincerely interested in the niche? Take a moment to promote it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule Service